The mechanism of the device is based on the
principle of traction, a method which simulates the human body natural
reaction to the application of physical force. Tissue cells react by
multiplying and the tissue gradually expands, a principle utilized by
various indigenous tribes for multiple doubling of the size of earlobes and
lips.
The Penis Extender has been tested on patients who have all obtained
lengthening of the penis after using the device in accordance with
instructions. The lengthening is permanent and does not entail a narrowing
of the circumference of the penis.
The test subjects achieved an average lengthening of the erected penis of
2.8 cm (24 per cent) after a treatment period of 3-4 months. The treatment
does not affect urination, sexual prowess or the power of reproduc-tion.
Lengthening can only be obtained by daily usage of the device and the effect
correlates with the number of hours of usage. The above mentioned results
were obtained after 12 hours? daily treatment over a period of 3 months.
DESCRIPTION OF THE VARIOUS COMPONENTS AND INSTRUCTION FOR ASSEMBLAGE
The Extender consists of a basal plastic ring (1) with a recess for the
urethra (2). The ring is fastened around the root of the penis. Two metal
bars, one with a right-handed thread (3), the other with a left-handed
thread (4) are attached to the basal ring. Inside each bar, hidden in a
tube, is a spring contrivance (5). At the distal end the two bars are
attached to a plastic support (6) with two holes, through which the ends of
a silicone tube are passed.
The components 1-5 are preassembled on
delivery. Depending on the size of the penis either the short or the long
extension bars are mounted by means of the round spanners provided (See fig.
3, page 9). The additional extension bars are required for later usage as
lengthening of the penis occurs. The plastic support is mounted by
introducing the ends of the bars (5) into the two big holes of the support.
The support is then pressed towards the basal ring (1). The springs are thus
pressed home. Pressure should be exerted until a snap or a click indicates
that the support is firmly secured to the bars.

INSTRUCTIONS FOR MOUNTING
The device is mounted by fastening the basal ring (1) around the root of the
penis, so that the two metal bars (2) run parallel with the penis, one on
each side, and the head of the penis rests in the bowl-shaped support (3).
By passing the two ends of the silicone tube through the holes in the
plastic support (4) a loop is made through which the head of the penis is
introduced. Before fastening of the penis the plastic support should be
pressed towards the body so that the two springs press home. The silicone
tube is fastened around the penis head by pulling the ends of the tube (5)
on the reverse side of the support. In men who have not been circumcised the
silicone tube is fitted just below the glans with the foreskin in place. The
ends are pressed into the two notches (6) to secure the fastening of the
penis head. Additional pieces of metal bar (7) may be added as required by
means of the two keys (8).

PROTECTION PAD ACCESSORY TO THE
Power-Exender.
In rare cases initial soreness can be experienced from using the Extender.
Such soreness is usually caused by initial excess of force, which should not
exeed 6-900 gram of traction for 4-8 hours daily during the first 2-3 weeks.
The force of the traction should then be increased to 900-1200 grams, and
the treatment period to 8-12 hours daily.
To relieve such occasional soreness, the
enclosed Protection Pad can be used in the following way:
- Expand the Protection Pad slowly.
- Fit it behind the penis glans, and allow it to contract to a snug fit.
- Mount the extra long silicone tube as usual.
The Protection Pad can be washed in lukewarm water, and new pads can be
purchased at your local Extender dealer or from this site.
INSTRUCTIONS FOR ADJUSTMENT
When the device has been fitted the force of trac-tion can be adjusted by
turning the two thumb-screws (1) in an inward direction. The actual force
exerted can be read on the hexagonal pistons (2) and the force of traction
can be varied from 600 to 900, 1200 or 1500 g (see fig. 4). Each marking on
the piston equals a traction force of 300 g. Thus, at the exertion of
maximum force (1500 g) only one marking is visible on the piston. A force of
600-900 g is recommended for the first 2-3 weeks and during that period the
Extender should not be worn for more than 4-5 hours a day. From then on the
force may be increased to 900-1200 g and to 12 hours daily usage of the
device. The Extender should be worn approximately 12 hours a day for a total
period of 3-6 months.
INSTRUCTIONS FOR USE AND DISMOUNTING OF THE
EXTENDER
During use of the Extender the penis can be held at any position except
sideways. In a pair of loose-fitting trousers the device is inconspicuous.
It can be worn at night but may become detached during uneasy sleep or
during a nightly erection. Accidental detachment merely requires re-mounting
of the device. The device is dismounted by loosening the silicone tube from
the ventral side of the support. The Extender can then be detached. The
thumbscrews are screwed home in an outward direction towards the basal ring.
When not in use the Extender can be left assembled or it can be disassembled
and placed in the box as required.

MATERIALS USED
1. Silicone type: WMQ, USP 21-4, PA/HP/exp3/(82)57/1984. Owing to its
chemical composition Silicone rubber is temperature resistant, weather
resistant and re-sistant to wear and tear. It is proof against exposure to
temperatures ranging from -65?? C to +210?? C.
2 + 4. Plastic parts: POM (Hostaform), C 2521
G Proof against temperatures ranging from -20?? C to +80??C.
3. Brass: CuZnS9Pb3 - W.no. 2.0401. Nitin
coating: Nitin is an intermetallic composition, combining the properties of
nickel and tin, which is produced by electrolytic depositing. Clinical
trials have demonstrated that Nitin coatings, despite their contents of 35%
nickel, do not seem to precipitate any reaction in nickel allergics.
5. Stainless steel springs: Din 17224 - W.no.
4310

CLEANING
The Power-Exender should be cleaned daily with soap and water. A chlorhexidine alcohol solution of 0.5% can be used for disinfection.
ENVIROMENTAL ASPECTS
The Power-Exender is delivered in packaging indispensable to shipment
of the device. Only environment friendly and reclycable materials are used.
 |